Pacific PR22-DDC Reservoir/Pump Combo
Pacific PR22-DDC Reservoir/Pump Combo is a reservoir and DDC pump combo unit kit. The combo features exceptional performances, the reservoir is 210mm long with 300ml capacity, and the DDC pump speed is 4600RPM. PR22-DDC is manufactured from high quality PPS and PMMA material to provide a crystal clear, high performance, durable solution. By giving users ideal mounting, fitting and flow, the PR22-DDC is easy to install. Upgrade your system with PR22-DDC Reservoir/Pump Combo.
Tt LCS Certified
Tt LCS Certified is a Thermaltake exclusive certification applied only to products that pass the design and hardcore enthusiast standards that a true LCS chassis should hold to. The Tt LCS certification was created so that we at Thermaltake can indicate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations, ensuring you get the best performance from the best features and fitment.
Driven Performance
Made in Taiwan, PR22-DDC top cap supports rubber washers for a proper seal, including
two predrilled G1/4” ports for fittings. Featuring 6mm thick of the pipe wall, PR22-DDC can sustain the maximum
pressure up to 21.75 PSI (Pounds per square inch). Also, users can easily open out the top cap, cleaning the reservoir
thoroughly.
Heat-resistant Acrylic Tank
PR22-DDC is made of reliable, light weighted PPS and PMMA construction, which is crystal clear and highly durable. High quality acrylic (PMMA) tube maximum working temperature: 131℉ (55℃).
Easy and Flexible Application
Along with two brackets connected to both ends, PR22-DDC is solid hold inside the chassis and allows enthusiasts to build up superior water cooling system from an aesthetic standpoint and incorporate externally-modular upgrades for their chassis. The Pacific PR22-DDC can be installed either horizontally or vertically, making the chassis out of the ordinary!
Cautions
Thermaltake recommends the following steps before using the Pacific series radiators and water blocks:
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000, for optimal performance and corrosion protection.
- Before storing your water cooling components, clean, rinse, and dry them to ensure a longer lifespan.
After completing your water loop setup, Thermaltake recommends:
- Use pre-mix coolant, such as Thermaltake Coolant 1000, for corrosion protection and performance.
- Fill the reservoir with coolant and power the pump on and off multiple times to ensure the loop is properly filled.
- DO NOT let the pump run dry. Turn off the power immediately if there is no liquid entering the pump.
- Fill the reservoir to the top to prevent air from entering the pump.
- If necessary, tilt the system to help bleed air from the loop.
- Place paper towels under fittings to test for leaks.
- Run the loop with the fill port open for about 24 hours to bleed air out completely.
- Flush the system correctly before starting to prevent any particles from sticking to your tubes and components.
- Coolant color might fade over time.
| P/N | CL-W250-PL00BL-A |
|---|---|
| Dimension (s) | 86.5 (L) x 62 (W) x 210.1 (H) |
| Material | PPS + PMMA |
| Capacity | 300 ml |
| Maximum head | 23 feet (7m) |
| Maximum Flow Rate | 522.38 L/h |
| Maximum pressure | 21.75 PSI |
| Input Voltage | 12 V |
| Power Input | 20 W |
| Connector | 4 Pin |
| Pump Speed | 4600 RPM |
| Screw Thread | G 1/4 |
| Parts | 1. Stopper *1 (G 1/4 ) 2. Bracket *2 |
User Manual
- File Name
- Description
- Size
- Version
- Release Date
-
Pacific PR22-DDC Reservoir/Pump Combo Manual
- Manual
- 855 KB
- 2019-05-21
